Home About News New Customer My Account My Cart All products Download Support
Products Get Started
Demos Contact Us
Browse products
All products
My account
My quotes
My cart
Click here for upcoming events ..

Switch v1.4 $12.55US $6.82US
excl. sales tax

A low power control signal switcher. Handles at most 10 Watt loads.

Application examples

  1. Advance your slide projector with each MIDI signal.
  2. Switch of lamps, small motors and other analog signals such as audio signals.

Technical specifications

Product Switch actuator
Version 1.4 (October 2011)
Actuator type reed relay
Switching power 10 W maximum
Switching voltage 200 V DC maximum
Switching current 0.5 A maximum
Switched output connector screw-terminal block
Control power 5 V DC, 2.5 mA
Power supply 5 V DC, 9 mA
Actuator dimensions 34 x 13 x 13 mm (1.3 x 0.51 x 0.51 inch)
Weight 20 g (0.7 oz), incl. cable
Cable 1.0 m (39 inch), shielded, red wire = power, black wire = ground, white wire = actuator input, maximum extension ? m (? ft)
Control connector male plug with 3 pins in a row spaced 2.54 mm (0.100 inch)
Software support
  1. Our EditorX software allows you to configure the digitizer to control multiple actuators simultaneously with on/off as well as PWM signals.
  2. Our Link software allows you to multiple actuators simultaneously with on/off signals.
Application notes
  1. Can be used directly with the USB-microDig actuator outputs (top row of the connector for sensors and actuators), as well as with the Digitizer outputs (ie. the power supply pins of inputs 25 - 32), as well as with a Wi-microDig with firmware v6.3 or higher.
  2. To use the Switch with a Wi-microDig with firmware v6.3 or higher move the pin of the Switch plug that is connected to the white wire to the free position between the ground and power pins (ie. the pins connected to the black and red wires). Use a pointy object, eg. a tiny screw driver or sharp knife to take the pin out of the slot by slightly depressing the metal lever through the cutout for the pin attached to the white wire. Then, after having taken out the pin, push the lever out again a bit so that after placing the pin in the slot between the red and black wires, the lever blocks the pin from coming out of the slot. You can see these steps on page 4 and 5 of the HackPlugs v1.0 manual.
  3. The two blue screw terminals are connected in-between one of the two wires that are used to supply power to the device you want to control or in between the wire that carries a signal you want to interrupt (or not). Cut one of these wires and strip the two ends so that the bare conductors can be inserted into the terminals. Then use a screw driver to secure the conductors in the terminals.
  4. If the Switch contacts remain closed even though the (control) power is off, try setting the (control) power on and off rapidly after each other. Eventually it should allow normal opening and closing of the contacts.

This page was updated on Thursday 01 August 2019.
Comments by customers Write Review
There are currently no comments on this product.
Customers who bought this product also purchased
SeeRGB v1.0
SeeRGB v1.0
Light2D v1.0
Light2D v1.0
Swipe3D v1.1
Swipe3D v1.1
SeeLaser-BlueWide v1.0
SeeLaser-BlueWide v1.0
ExtendCableD-10 v1.0
ExtendCableD-10 v1.0
ReachCloseD v1.0
ReachCloseD v1.0
Product Search

Advanced Search
Comments more
Write ReviewWrite a comment on this product!
New Customers

Need help?



User forums

Linkedin group LinkedIn group

Facebook page Facebook page
Instant SSL