I-CubeX Online Store - TouchGlove-L v1.8 : Contact glove sensor for right hand

TouchGlove-L v1.8 (obsolete)

A controller for drum machines at your fingertips. A very expressive and natural sensor. Includes 6 pressure sensors per glove - five on the fingertips and one on the palm. Each sensor responds to pressure from approx. 10 KPa (0.10 Kg/cm2, 1.5 PSI) to 981 KPa (10.0 Kg/cm2, 142 PSI) or approx. 0.2 N (20 g, 0.04 lb) to 98 N (10 Kg, 22 lb) that's evenly applied across its active area, a 5 mm (0.2 inch) diameter disk. Tune the TouchGlove using the online manual. Available in left hand (TouchGlove v1.8-R) and left hand (TouchGlove v1.8-L) version.

Application examples

Uses the same sensor as in the TouchMicro-5, so why don't you add a few of those for more sensitivity.
Use as touch controller, eg. for a synthesizer. Check out the Virtual Drum Set that was made with a left-hand and right-hand TouchGlove, or the Invisible Violin that was made with the left-hand TouchGlove by Tim Soo.
Combine with the BendShort, BendMini or BendMicro and create your own custom dataglove (add some punch with a GForce3D-6).
For whole-body expression go bodysuit, capture all your joints' movements and express with all your extremities. Combine with BendMicro, BendMini and BendShort sensors from finger to toe. A GForce3D-6 on each of your feet and hands captures kicks and punches. A Hot will keep you in check of your body temp. Use the TouchGlove on both hands to always be able to touch-control your performance, even while doing a handstand.
A wireless Wi-microSystem is recommended in all cases to operate without tether.

Technical specifications

Product TouchGlove-L sensor

Version 1.8 (May 2013)

Sensing parameter contact pressure or force of 5 fingertips and one palmpad

Sensing technology zero-travel force sensitive resistor

Active area 5 mm (0.2 inch) diameter disk for 5 fingertips and one palmpad

Range (each sensor) approx. 10 KPa (0.10 Kg/cm2, 1.5 PSI) to 981 KPa (10.0 Kg/cm2, 142 PSI) or approx. 0.2 N (20 g, 0.04 lb) to 98 N (10 Kg, 22 lb), evenly applied across active area

Response time 1 to 2 ms (mechanical)

Output resistance more than 100 KOhm (at 0 N) to 200 Ohm (at 98 N) in parallel with 47 KOhm

Power supply 1.0 to 10 V DC, 0.1 mA at 5 V

Operating temperature -20° to 100° C (-4° to 212° C)

Glove stretchy black nylon, medium size only, right or left hand

Weight 70 g (2.5 oz), incl. cable

Cable 0.90 m (35 inch), twisted, unshielded, red wire = power, black wire = ground, white wire = sensor output

Connector male plug with 3 pins in a row spaced 2.54 mm (0.100 inch)

Software support

09 Dec 2014: SensorX v1.00 for MacOS and Windows (64bit, contact us for the 32bit version) from source code in Max. For multiple sensors or sensor outputs, run multiple instances of the application, each started in its own folder. Use together with Connect (MacOS / Windows) or BlueMIDI (Windows).

07 Dec 2014: TouchGloves v2.01 for MacOS and Windows (64bit, contact us for the 32bit version) from source code in Max. Use together with Connect (MacOS / Windows) or BlueMIDI (Windows).

24 Nov 2013: TouchGloves v1.1 for MacOS and Windows from source code in Max.

Application notes

Requires extremely careful handling. Do not rush when putting the glove on or off. Do not stretch fabric excessively. Gradually put on or take off glove by sliding each finger in turn a small distance in or out of the glove. Make sure to pull the fabric at the junction between two fingers and not at the tip of the fingers.

Please read the TouchGlove manual.

For calibration information, see the TouchMicro-5

The sensors may show a value even when fingers or palm are not touching anything. This is caused by the fabric being stretched around and/or pushing on the sensor. To resolve this, use our software to adjust the range of the sensor.