Home About News New Customer My Account My Cart All products Download Support
Products Get Started
Demos Contact Us
Shop
Browse products
All products
My account
My quotes
My cart
Login
Currency:
Events
Click here for upcoming events ..


Checkout
SwitchPower v1.1 $15.79US
 
2 - 6 : $15.00US ( save 5% )
7 - 19 : $14.21US ( save 10% )
20 + : $12.64US ( save 20% )
excl. sales tax

The powerful uncle of the Switch. Handles 300 Watt DC / 2.5 kW AC loads.

Application examples

  1. Switch of lamps, motors and other devices.

Technical specifications

Product SwitchPower actuator
Version 1.1 (February 2021)
Actuator type relay
Switching power 300 W DC / 2.5 kW AC maximum
Switching voltage 30 V DC / 250 V AC maximum
Switching current 10 A maximum
Switched output connector screw-terminal block with NC (normally closed), COM (common) and NO (normally open) terminals
Control power 5 V DC, 2.5 mA
Power supply 5 V DC, 72 mA (max)
Dimensions 43 x 18 x 18 mm (1.7 x 0.71 x 0.71 inch)
Mounting no mounting holes
Cable 1.0 m (39 inch), shielded, red wire = power, black wire = ground, white wire = actuator input, extendable at least 100 m (328 ft) with ExtendCableD-10
Connector male 1x4 plug with 3 pins in a row spaced 2.54 mm (0.100 inch)
Weight 22 g (0.78 oz), incl. cable
Software support
  1. Our EditorX software allows you to configure the digitizer to control multiple actuators simultaneously with on/off as well as PWM signals.
  2. Our Link software allows you to multiple actuators simultaneously with on/off signals.
Application notes
  1. Can be used directly with the WiDig or USB-microDig actuator outputs (ie. the top row of the connector for sensors and actuators), as well as with the Digitizer outputs (ie. the power supply pins of inputs 25 - 32), or a Wi-microDig with firmware v6.3.
  2. To use the actuator with a Digitizer, use header cables such as in the AdaptCableKit so that the white wire is connected to one of the switched power supply pins of inputs 25 - 32 and the red wire is connected to the power supply pins of any of the other inputs.
  3. To use the SwitchPower with a Wi-microDig with firmware v6.3 move the pin of the SwitchPower plug that is connected to the white wire to the free position between the ground and power pins (ie. the pins connected to the black and red wires). Use a pointy object, eg. a tiny screw driver or sharp knife to take the pin out of the slot by slightly depressing the metal lever through the cutout for the pin attached to the white wire. Then, after having taken out the pin, push the lever out again a bit so that after placing the pin in the slot between the red and black wires, the lever blocks the pin from coming out of the slot. You can see these steps on page 4 and 5 of the HackPlugs v1.0 manual.
  4. Connect the terminal named "COM" (for "common") and one of the other terminals between one of the two wires that are used to supply power to the device you want to control or between the wire that carries a signal you want to interrupt (or not). Cut one of these wires and strip the two ends so that the bare conductors can be inserted into the terminals. Then use a screw driver to secure the conductors in the terminals.
  5. When the terminal named "COM" and the terminal on its right are connected the COM terminal is not connected to the other terminal on its left, and vice versa. Simply select the terminals such that when you set the SwitchPower on or off, that the state of the device is as per your needs.

This page was updated on Friday 22 October 2021.
Comments by customers Write Review
There are currently no comments on this product.
Customers who bought this product also purchased
Hold-003 v1.0
Hold-003 v1.0
Vent v1.0
Vent v1.0
Drive-L298N v1.0
Drive-L298N v1.0
Poke-001 v1.0
Poke-001 v1.0
CVolt v1.0
CVolt v1.0
MotorServo-015 v1.0
MotorServo-015 v1.0
Product Search




Advanced Search
Comments more
Write ReviewWrite a comment on this product!
Support
New Customers

Need help?

Resources

Downloads

User forums

Linkedin group LinkedIn group

Facebook page Facebook page