Home About News New Customer My Account My Cart All products Download Support
Products Get Started
Demos Contact Us
Browse products
All products
My account
My quotes
My cart
Click here for upcoming events ..

FeelVibe v1.5 $20.15US
2 - 6 : $19.15US ( save 5% )
7 - 19 : $18.14US ( save 10% )
20 + : $16.13US ( save 20% )
excl. sales tax

A vibrating actuator which provides haptic and tactile feedback in a variety of ways.

Application examples

  1. Make it jiggle, wiggle, twitch, shimmy, joggle, wag, wobble, shake, twist, squirm, writhe .. !
  2. Give vibro-tactile feedback to objects if a visitor touches them (detect the touch with Touch sensor).

Technical specifications

Product FeelVibe actuator
Version 1.5 (May 2017)
Actuator type Eccentric Rotating Mass (ERM) motor
Power supply 4.75 to 5.25 V DC, ? mA (average) at 5 V
Dimensions 30 x 22 x 10 mm (1.2 x 0.87 x 0.39 inch)
Cable 1.0 m (39 inch), shielded, red wire = power, black wire = ground, white wire = actuator control, extendable at least 100 m (328 ft) with ExtendCableD-10
Mounting four 1.7 mm (0.067 inch) mounting holes spaced apart 20 mm (0.79 inch) width-wise and length-wise
Connector male 1x4 plug with 3 pins in a row spaced 2.54 mm (0.100 inch)
Weight 14 g (0.49 oz), incl. cable
Software support
  1. Our EditorX software allows you to configure the digitizer to control multiple actuators simultaneously with on/off as well as PWM signals.
  2. Our Link software allows you to multiple actuators simultaneously with on/off signals.
Application notes
  1. Make sure the actuator is plugged into the digitizer with the red wire connected to power. Reversing the plug or applying power with reverse polarity may cause damage to the actuator.
  2. Can be used directly with the WiDig or USB-microDig actuator outputs (top row of the connector for sensors and actuators), as well as with a Wi-microDig with firmware v6.3 or higher. Can also be used with the Digitizer outputs (ie. the power supply pins of inputs 25 - 32) but the white wire needs to be connected to the same pin as the red wire.
  3. To use the actuator with a Wi-microDig with firmware v6.3 move the pin of the plug that is connected to the white wire to the free position between the ground and power pins (ie. the pins connected to the black and red wires). Use a pointy object, eg. a tiny screw driver or sharp knife to take the pin out of the slot by slightly depressing the metal lever through the cutout for the pin attached to the white wire. Then, after having taken out the pin, push the lever out again a bit so that after placing the pin in the slot between the red and black wires, the lever blocks the pin from coming out of the slot. You can see these steps on page 4 and 5 of the HackPlugs v1.0 manual.
  4. Can be controlled with on (5V) / off (0V) signals, as well as pulse width modulated (PWM) signals.

This page was updated on Thursday 02 September 2021.
Comments by customers Write Review
There are currently no comments on this product.
Customers who bought this product also purchased
Drive-FR120N v1.0
Drive-FR120N v1.0
MoveOn v1.8
MoveOn v1.8
AngleD v1.2
AngleD v1.2
EncloseSensor v1.0
EncloseSensor v1.0
Angle v1.0
Angle v1.0
EncloseMini v1.0
EncloseMini v1.0
Product Search

Advanced Search
Comments more
Write ReviewWrite a comment on this product!
New Customers

Need help?



User forums

Linkedin group LinkedIn group

Facebook page Facebook page