Difference between revisions of "Firmware-63 Messages"
(Created page with "Note that in the following listing the commands as echoed back by the Wi-microDig (to allow multiple Max/MSP objects to work with a Wi-microDig) are not included. Since many f...") |
(→Dual Mode) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
Note that in the following listing the commands as echoed back by the Wi-microDig (to allow multiple Max/MSP objects to work with a Wi-microDig) are not included. | Note that in the following listing the commands as echoed back by the Wi-microDig (to allow multiple Max/MSP objects to work with a Wi-microDig) are not included. | ||
| − | Since many firmware 6. | + | Since many firmware 6.3 messages are the same as used in firmware 7.3, reference is made to firmware 7.3 information where applicable. |
| Line 9: | Line 9: | ||
*[[Firmware-73_Message-071 |VERSION (71, 47h)]] | *[[Firmware-73_Message-071 |VERSION (71, 47h)]] | ||
*[[Firmware-73_Message-091 |MODE (91, 5Bh)]] | *[[Firmware-73_Message-091 |MODE (91, 5Bh)]] | ||
| − | *[[Firmware-73_Message-095 | | + | *[[Firmware-73_Message-095 |MIDI STATUS (95, 60h)]] |
*[[Firmware-63_Message-111 |LOW POWER LEVEL (111, 6Fh)]] | *[[Firmware-63_Message-111 |LOW POWER LEVEL (111, 6Fh)]] | ||
*[[Firmware-63_Message-114 |BATTERY VOLTAGE LEVEL (114, 6Fh)]] | *[[Firmware-63_Message-114 |BATTERY VOLTAGE LEVEL (114, 6Fh)]] | ||
| Line 24: | Line 24: | ||
*[[Firmware-73_Message-000 |STREAM DATA (0, 00h)]] | *[[Firmware-73_Message-000 |STREAM DATA (0, 00h)]] | ||
*[[Firmware-73_Message-004 |SAMPLE DATA (4, 04h)]] | *[[Firmware-73_Message-004 |SAMPLE DATA (4, 04h)]] | ||
| − | *[[Firmware-73_Message-010 |I2C DATA (10, | + | *[[Firmware-73_Message-010 |I2C DATA (10, 0Ah)]] |
*[[Firmware-73_Message-125 |I2C PORT (125, 7Dh)]] | *[[Firmware-73_Message-125 |I2C PORT (125, 7Dh)]] | ||
*[[Firmware-73_Message-123 |I2C NO RESPONSE (123, 7Bh)]] | *[[Firmware-73_Message-123 |I2C NO RESPONSE (123, 7Bh)]] | ||
*[[Firmware-73_Message-126 |I2C WRITE (126, 7Eh)]] | *[[Firmware-73_Message-126 |I2C WRITE (126, 7Eh)]] | ||
*[[Firmware-73_Message-127 |I2C READ (127, 7Fh)]] | *[[Firmware-73_Message-127 |I2C READ (127, 7Fh)]] | ||
Latest revision as of 17:08, 19 June 2017
Note that in the following listing the commands as echoed back by the Wi-microDig (to allow multiple Max/MSP objects to work with a Wi-microDig) are not included. Since many firmware 6.3 messages are the same as used in firmware 7.3, reference is made to firmware 7.3 information where applicable.
General
- RESET ACK (35, 23h)
- STATUS (37, 25h)
- VERSION (71, 47h)
- MODE (91, 5Bh)
- MIDI STATUS (95, 60h)
- LOW POWER LEVEL (111, 6Fh)
- BATTERY VOLTAGE LEVEL (114, 6Fh)
Standalone Mode
