Difference between revisions of "Firmware-633 Command-049"
(Copied from Firmware-73 Command-049, revision 1951) |
|||
| Line 1: | Line 1: | ||
SET OUTPUT INIT (49, 31h) | SET OUTPUT INIT (49, 31h) | ||
| − | The SET OUTPUT INIT command sets the output status at power-up of the USB-microDig | + | The SET OUTPUT INIT command sets the output status at power-up of the USB-microDig. The command can be used in both host and stand-alone modes of operation. All output settings are stored in both volatile and non-volatile memory. After a RESET of the USB-microDig, all outputs’ statuses are retrieved from non-volatile memory whether in stand-alone mode or in host mode. Upon completion of the command the digitizer sends out the same command. To get the values stored in non-volatile memory, use the [[Firmware-633 Command-059 |DUMP OUTPUT INIT command]]. |
The [BODY] of the SET OUTPUT INIT command consists of two 7-bit bytes with the following format: | The [BODY] of the SET OUTPUT INIT command consists of two 7-bit bytes with the following format: | ||
| Line 13: | Line 13: | ||
|- | |- | ||
| | | | ||
| − | |p = 1; | + | |p = [0..1]; setting without effect |
| − | |||
| − | |||
| − | |||
|- | |- | ||
| | | | ||
|yyy = [0..7]; actuator output number, where the first actuator output number = 0, and the last (8th) actuator output number = 7 | |yyy = [0..7]; actuator output number, where the first actuator output number = 0, and the last (8th) actuator output number = 7 | ||
|- | |- | ||
| − | |0zzzzzzz: | + | |0zzzzzzz: |
| − | |zzzzzzz = [0..127]; | + | |zzzzzzz = [0..127]; setting without effect |
|} | |} | ||
Example: | Example: | ||
| − | In order to | + | In order to turn the 2nd actuator output on, ie. to 5V, the following message is sent: |
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | :240, 125, 0 {DEV}, 49 {SET OUTPUT INIT}, 65 {x = 1, p = 0, yyy = 1}, 0, 247 (F0h, 7Dh, 00h, 30h, 41h, 00h, F7h) | |
| − | + | In order to turn the same actuator output off, ie. to 0V, the following message is sent: | |
| − | + | :240, 125, 0 {DEV}, 49 {SET OUTPUT INIT}, 1 {x = 0, p = 0, yyy = 1}, 0, 247 (F0h, 7Dh, 00h, 30h, 01h, 00h F7h) | |
Latest revision as of 21:49, 11 January 2018
SET OUTPUT INIT (49, 31h)
The SET OUTPUT INIT command sets the output status at power-up of the USB-microDig. The command can be used in both host and stand-alone modes of operation. All output settings are stored in both volatile and non-volatile memory. After a RESET of the USB-microDig, all outputs’ statuses are retrieved from non-volatile memory whether in stand-alone mode or in host mode. Upon completion of the command the digitizer sends out the same command. To get the values stored in non-volatile memory, use the DUMP OUTPUT INIT command.
The [BODY] of the SET OUTPUT INIT command consists of two 7-bit bytes with the following format:
| 0xp00yyy: | x = 1; output on |
| x = 0; output off | |
| p = [0..1]; setting without effect | |
| yyy = [0..7]; actuator output number, where the first actuator output number = 0, and the last (8th) actuator output number = 7 | |
| 0zzzzzzz: | zzzzzzz = [0..127]; setting without effect |
Example:
In order to turn the 2nd actuator output on, ie. to 5V, the following message is sent:
- 240, 125, 0 {DEV}, 49 {SET OUTPUT INIT}, 65 {x = 1, p = 0, yyy = 1}, 0, 247 (F0h, 7Dh, 00h, 30h, 41h, 00h, F7h)
In order to turn the same actuator output off, ie. to 0V, the following message is sent:
- 240, 125, 0 {DEV}, 49 {SET OUTPUT INIT}, 1 {x = 0, p = 0, yyy = 1}, 0, 247 (F0h, 7Dh, 00h, 30h, 01h, 00h F7h)
