|
|
| Line 1: |
Line 1: |
| − | The Options section sets the sample interval, mode of operation and muting. | + | The Data section sets the MIDI output port, OSC status and recording status. |
| | | | |
| − | [[File:editorx-73_options.png]] | + | [[File:editorx-73_data.png]] |
| | | | |
| − | ==Sampling Interval==
| |
| | | | |
| − | The sampling interval can be set between a minimum and a maximum value, in milliseconds. The minimum value is 1 ms. The maximum value is 16383 ms, ie. about 16 seconds. Setting the sampling interval to its minimum may result in a delayed response of EditorX or whichever software or device that is receiving the MIDI messages as it may be overwhelmed by the number of MIDI messages. It is often not useful to set the sampling interval to its minimum given that many sensors don't update as frequently as the sampling interval implies. Consult the product page of the sensor to determine the sensor's update rate. The theoretical sampling rate in Hertz (Hz) can be derived from the sampling interval using the formula 1000 / sampling_interval. Note however, that, depending on its configuration, the digitizer easily takes more than 1 ms to complete all processing so that the actual sampling rate will be lower than implied by the sampling interval. See also the [[Firmware-810_Command-013 |INTERVAL]] and [[Firmware-810_Command-013 |DUMP INTERVAL]] commands.
| + | ==MIDI output port== |
| | | | |
| − | ==Mode==
| + | This pull-down menu selects the MIDI port to which messages from the sensor inputs are to be forwarded. You may need to click "Update" to see all available ports. The port cannot be stored in the digitizer but it can be saved in a preset. |
| | | | |
| − | The mode of operation can be set as standalone or host. EditorX sets a digitizer to standalone mode immediately after establishing a connection with a digitizer since EditorX can only configure the standalone mode settings of a digitizer. In standalone mode the configuration is stored in a digitizer so that it can be used without requiring a computer to configure it each time before using it. In standalone mode the digitizer is outputting data ready for use by the receiving device(s). If the sensor input is mapped to actuator outputs, the receiving device(s) would include the actuators. See also the [[Firmware-810_Command-090 |SET MODE]] command.
| |
| | | | |
| | + | ==OSC== |
| | | | |
| − | ==Muting==
| + | EditorX can be configured to output and/or receive OSC (Open Sound Control) messages. The Edit button opens the [[EditorX-81_OSC | OSC]] window. The On/Off button enables/disables sending and receiving of OSC messages. To use the OSC feature EditorX has to stay running. |
| | | | |
| − | Muting can be set to on or off, and configures the digitizer to stop sampling of all sensor inputs so that no data is output by the digitizer. Changing the mode of operation of the digitizer, clearing the configuration to default settings or re-powering the digitizer turns off muting, ie. enables sampling of sensor inputs again. See also the [[Firmware-810_Command-050 |SET MUTE]] command.
| |
| | | | |
| | + | ==Recording== |
| | | | |
| − | ==OSC==
| + | The Edit button opens the [[EditorX-81_Recording | Recording]] window. The Start/Stop button starts/stops recording. To use the recording feature EditorX has to stay running. |
| − | | |
| − | EditorX can be configured to output and/or receive OSC (Open Sound Control) messages. The Edit button opens the [[EditorX-81_OSC | OSC]] window. The On/Off button enables/disables sending and receiving of OSC messages. To use the OSC feature EditorX has to stay running.
| |
Revision as of 19:25, 29 November 2018
The Data section sets the MIDI output port, OSC status and recording status.
File:Editorx-73 data.png
MIDI output port
This pull-down menu selects the MIDI port to which messages from the sensor inputs are to be forwarded. You may need to click "Update" to see all available ports. The port cannot be stored in the digitizer but it can be saved in a preset.
OSC
EditorX can be configured to output and/or receive OSC (Open Sound Control) messages. The Edit button opens the OSC window. The On/Off button enables/disables sending and receiving of OSC messages. To use the OSC feature EditorX has to stay running.
Recording
The Edit button opens the Recording window. The Start/Stop button starts/stops recording. To use the recording feature EditorX has to stay running.
