Difference between revisions of "Firmware-640 Commands"
(Copied from Firmware-633 Commands, revision 2410) |
|||
| Line 1: | Line 1: | ||
| − | Since many firmware 6. | + | Since many firmware 6.4 commands are the same as used in firmware 7.4, reference is made to firmware 7.4 information where applicable. |
==General== | ==General== | ||
| Line 5: | Line 5: | ||
This section describes the messages and commands for resetting the Wi-microDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting MIDI out operation, setting running status and obtaining the Bluetooth port status. These commands have the same effect both in stand-alone and host mode. | This section describes the messages and commands for resetting the Wi-microDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting MIDI out operation, setting running status and obtaining the Bluetooth port status. These commands have the same effect both in stand-alone and host mode. | ||
| − | *[[Firmware- | + | *[[Firmware-740 Command-034 |RESET (34, 22h)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-060 |OUTPUT INIT (60, 3Ch)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-071 |DUMP VERSION (71, 47h)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-066 |DUMP FIRMWARE VERSION (66, 42h)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-090 |SET MODE (90, 5Ah)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-091 |DUMP MODE (91, 5Bh)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-092 |SET ID (92, 5Ch)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-032 |TOGGLE MUTE (32, 20h)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-050 |SET MUTE (50, 32h)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-051 |DUMP MUTE (51, 33h)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-094 |MIDI STATUS (94, 5Eh)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-095 |DUMP MIDI STATUS (95, 5Fh)]] |
| − | *[[Firmware- | + | *[[Firmware-640 Command-111 |LOW POWER LEVEL (111, 6Fh)]] |
| − | *[[Firmware- | + | *[[Firmware-640 Command-114 |BATTERY VOLTAGE LEVEL (114, 6Fh)]] |
| Line 31: | Line 31: | ||
This section describes the programming protocol commands sent to the USB-microDig specifically for stand-alone mode. | This section describes the programming protocol commands sent to the USB-microDig specifically for stand-alone mode. | ||
| − | *[[Firmware- | + | *[[Firmware-740 Command-100 |EDIT NAME (100, 64h)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-101 |DUMP NAME (101, 65h)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-105 |CLEAR CONFIG (105, 69h)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-106 |EDIT CONFIG (106, 6Ah)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-107 |DUMP CONFIG (107, 6Bh)]] |
==Dual Mode== | ==Dual Mode== | ||
| Line 42: | Line 42: | ||
This section describes the programming protocol commands sent to the USB-microDig to configure sensor inputs and actuator outputs that can be used in both host mode and stand-alone mode. | This section describes the programming protocol commands sent to the USB-microDig to configure sensor inputs and actuator outputs that can be used in both host mode and stand-alone mode. | ||
| − | *[[Firmware- | + | *[[Firmware-740 Command-001 |STREAM (1, 01h)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-011 |DUMP STREAM (11, 0Bh)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-002 |RES (2, 02h)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-012 |DUMP RES (12, 0Ch)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-004 |SAMPLE (4, 04h)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-003 |INTERVAL (3, 03h)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-013 |DUMP INTERVAL (13, 0Dh)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-008 |FUNCTION (8, 08h)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-018 |DUMP FUNCTION (18, 12h)]] |
| − | *[[Firmware- | + | *[[Firmware-740 Command-125 |I2C PORT (125, 7Dh)]] |
| − | + | *[[Firmware-740 Command-126 |I2C WRITE (126, 7Eh)]] | |
| − | + | *[[Firmware-740 Command-124 |I2C WRITE SINGLE (124, 7Ch)]] | |
| − | + | *[[Firmware-740 Command-127 |I2C READ (127, 7Fh)]] | |
| − | + | *[[Firmware-740 Command-122 |I2C READ SINGLE (122, 7Ah)]] | |
| − | |||
| − | *[[Firmware- | ||
| − | *[[Firmware- | ||
| − | *[[Firmware- | ||
| − | *[[Firmware- | ||
Revision as of 20:31, 4 December 2018
Since many firmware 6.4 commands are the same as used in firmware 7.4, reference is made to firmware 7.4 information where applicable.
General
This section describes the messages and commands for resetting the Wi-microDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting MIDI out operation, setting running status and obtaining the Bluetooth port status. These commands have the same effect both in stand-alone and host mode.
Standalone Mode
This section describes the programming protocol commands sent to the USB-microDig specifically for stand-alone mode.
Dual Mode
This section describes the programming protocol commands sent to the USB-microDig to configure sensor inputs and actuator outputs that can be used in both host mode and stand-alone mode.
