Difference between revisions of "Firmware-760 Messages"
(Copied from Firmware-751 Messages, revision 3199) |
|||
| Line 1: | Line 1: | ||
Note that in the following listing the commands as echoed back by the USB-microDig (to allow multiple Max/MSP objects to work with a USB-microDig) are not included. | Note that in the following listing the commands as echoed back by the USB-microDig (to allow multiple Max/MSP objects to work with a USB-microDig) are not included. | ||
| + | |||
| + | Since many firmware 7.60 commands are the same as used in firmware 8.10/7.51, reference is made to firmware 8.10/7.51 information where applicable. | ||
==General== | ==General== | ||
| − | *[[Firmware- | + | *[[Firmware-810_Message-035 |RESET ACK (35, 23h)]] |
| − | *[[Firmware- | + | *[[Firmware-810_Message-037 |STATUS (37, 25h)]] |
| − | *[[Firmware- | + | *[[Firmware-810_Message-051 |MUTE (51, 33h)]] |
| − | *[[Firmware- | + | *[[Firmware-810_Message-071 |VERSION (71, 47h)]] |
| − | *[[Firmware- | + | *[[Firmware-810_Message-091 |MODE (91, 5Bh)]] |
*[[Firmware-751_Message-096 |MIDI OUT (96, 60h)]] | *[[Firmware-751_Message-096 |MIDI OUT (96, 60h)]] | ||
*[[Firmware-751_Message-095 |MIDI STATUS (95, 60h)]] | *[[Firmware-751_Message-095 |MIDI STATUS (95, 60h)]] | ||
| Line 16: | Line 18: | ||
==Standalone Mode== | ==Standalone Mode== | ||
| − | *[[Firmware- | + | *[[Firmware-810_Message-101 |NAME (101, 65h)]] |
| − | *[[Firmware- | + | *[[Firmware-810_Message-106 |CONFIG (106, 6Ah)]] |
==Dual Mode== | ==Dual Mode== | ||
| − | *[[Firmware- | + | *[[Firmware-810_Message-000 |STREAM DATA (0, 00h)]] |
| − | *[[Firmware- | + | *[[Firmware-810_Message-004 |SAMPLE DATA (4, 04h)]] |
| − | *[[Firmware- | + | *[[Firmware-810_Message-010 |I2C DATA (10, 0Ah)]] |
| − | *[[Firmware- | + | *[[Firmware-810_Message-125 |I2C PORT (125, 7Dh)]] |
| − | *[[Firmware- | + | *[[Firmware-810_Message-123 |I2C NO RESPONSE (123, 7Bh)]] |
| − | *[[Firmware- | + | *[[Firmware-810_Message-126 |I2C WRITE (126, 7Eh)]] |
| − | *[[Firmware- | + | *[[Firmware-810_Message-127 |I2C READ (127, 7Fh)]] |
Revision as of 20:55, 4 December 2018
Note that in the following listing the commands as echoed back by the USB-microDig (to allow multiple Max/MSP objects to work with a USB-microDig) are not included.
Since many firmware 7.60 commands are the same as used in firmware 8.10/7.51, reference is made to firmware 8.10/7.51 information where applicable.
General
- RESET ACK (35, 23h)
- STATUS (37, 25h)
- MUTE (51, 33h)
- VERSION (71, 47h)
- MODE (91, 5Bh)
- MIDI OUT (96, 60h)
- MIDI STATUS (95, 60h)
- COM STATUS (111, 6Fh)
Standalone Mode
