Difference between revisions of "Firmware-740 Commands"
| (2 intermediate revisions by the same user not shown) | |||
| Line 8: | Line 8: | ||
*[[Firmware-810 Command-060 |OUTPUT INIT (60, 3Ch)]] | *[[Firmware-810 Command-060 |OUTPUT INIT (60, 3Ch)]] | ||
| + | *[[Firmware-810 Command-066 |DUMP FIRMWARE VERSION (66, 42h)]] | ||
*[[Firmware-810 Command-071 |DUMP VERSION (71, 47h)]] | *[[Firmware-810 Command-071 |DUMP VERSION (71, 47h)]] | ||
| − | |||
*[[Firmware-810 Command-090 |SET MODE (90, 5Ah)]] | *[[Firmware-810 Command-090 |SET MODE (90, 5Ah)]] | ||
| Line 16: | Line 16: | ||
*[[Firmware-810 Command-092 |SET ID (92, 5Ch)]] | *[[Firmware-810 Command-092 |SET ID (92, 5Ch)]] | ||
| − | *[[Firmware-810 Command-032 | | + | *[[Firmware-810 Command-032 |SET SOLO (32, 20h)]] |
| + | *[[Firmware-810 Command-033 |DUMP SOLO (33, 21h)]] | ||
*[[Firmware-810 Command-050 |SET MUTE (50, 32h)]] | *[[Firmware-810 Command-050 |SET MUTE (50, 32h)]] | ||
*[[Firmware-810 Command-051 |DUMP MUTE (51, 33h)]] | *[[Firmware-810 Command-051 |DUMP MUTE (51, 33h)]] | ||
| Line 58: | Line 59: | ||
*[[Firmware-810 Command-008 |FUNCTION (8, 08h)]] | *[[Firmware-810 Command-008 |FUNCTION (8, 08h)]] | ||
*[[Firmware-810 Command-018 |DUMP FUNCTION (18, 12h)]] | *[[Firmware-810 Command-018 |DUMP FUNCTION (18, 12h)]] | ||
| + | |||
| + | *[[Firmware-810 Command-020 |TABLE ENTRY (20, 14h)]] | ||
| + | *[[Firmware-810 Command-030 |DUMP TABLE ENTRY (30, 1Eh)]] | ||
| + | *[[Firmware-810 Command-031 |DUMP TABLE (31, 1Fh)]] | ||
*[[Firmware-810 Command-047 |SET OUTPUT PULSE (47, 2Fh)]] | *[[Firmware-810 Command-047 |SET OUTPUT PULSE (47, 2Fh)]] | ||
Latest revision as of 15:44, 8 November 2019
Since many firmware 7.40 commands are the same as used in firmware 8.10/7.3, reference is made to firmware 8.10/7.3 information where applicable.
General
This section describes the messages and commands for resetting the USB-microDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting MIDI out operation, setting running status and obtaining COM port status. These commands have the same effect both in stand-alone and host mode.
Standalone Mode
This section describes the programming protocol commands sent to the USB-microDig specifically for stand-alone mode.
- CLEAR CONFIG (105, 69h)
- EDIT CONFIG (106, 6Ah)
- DUMP CONFIG (107, 6Bh)
- DUMP ALL CONFIG (108, 6Ch)
- DUMP CONFIG RANGE (109, 6Dh)
Dual Mode
This section describes the programming protocol commands sent to the USB-microDig to configure sensor inputs and actuator outputs that can be used in both host mode and stand-alone mode.
