Difference between revisions of "Firmware-751 Commands"
| Line 4: | Line 4: | ||
This section describes the messages and commands for resetting the USB-microDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting MIDI out operation, setting running status and obtaining COM port status. These commands have the same effect both in stand-alone and host mode. | This section describes the messages and commands for resetting the USB-microDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting MIDI out operation, setting running status and obtaining COM port status. These commands have the same effect both in stand-alone and host mode. | ||
| − | *[[Firmware- | + | *[[Firmware-751 Command-034 |RESET (34, 22h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-060 |OUTPUT INIT (60, 3Ch)]] |
*[[Firmware-751 Command-071 |DUMP VERSION (71, 47h)]] | *[[Firmware-751 Command-071 |DUMP VERSION (71, 47h)]] | ||
*[[Firmware-751 Command-066 |DUMP FIRMWARE VERSION (66, 42h)]] | *[[Firmware-751 Command-066 |DUMP FIRMWARE VERSION (66, 42h)]] | ||
| − | *[[Firmware- | + | *[[Firmware-751 Command-090 |SET MODE (90, 5Ah)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-091 |DUMP MODE (91, 5Bh)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-092 |SET ID (92, 5Ch)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-032 |TOGGLE MUTE (32, 20h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-050 |SET MUTE (50, 32h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-051 |DUMP MUTE (51, 33h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-093 |MIDI OUT (93, 5Dh)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-096 |DUMP MIDI OUT (96, 60h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-094 |MIDI STATUS (94, 5Eh)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-095 |DUMP MIDI STATUS (95, 5Fh)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-111 |DUMP COM STATUS (111, 6Fh)]] |
| Line 32: | Line 32: | ||
This section describes the programming protocol commands sent to the USB-microDig specifically for stand-alone mode. | This section describes the programming protocol commands sent to the USB-microDig specifically for stand-alone mode. | ||
| − | *[[Firmware- | + | *[[Firmware-751 Command-100 |EDIT NAME (100, 64h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-101 |DUMP NAME (101, 65h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-105 |CLEAR CONFIG (105, 69h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-106 |EDIT CONFIG (106, 6Ah)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-107 |DUMP CONFIG (107, 6Bh)]] |
| Line 44: | Line 44: | ||
This section describes the programming protocol commands sent to the USB-microDig to configure sensor inputs and actuator outputs that can be used in both host mode and stand-alone mode. | This section describes the programming protocol commands sent to the USB-microDig to configure sensor inputs and actuator outputs that can be used in both host mode and stand-alone mode. | ||
| − | *[[Firmware- | + | *[[Firmware-751 Command-001 |STREAM (1, 01h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-011 |DUMP STREAM (11, 0Bh)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-002 |RES (2, 02h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-012 |DUMP RES (12, 0Ch)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-004 |SAMPLE (4, 04h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-003 |INTERVAL (3, 03h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-013 |DUMP INTERVAL (13, 0Dh)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-008 |FUNCTION (8, 08h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-018 |DUMP FUNCTION (18, 12h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-020 |TABLE ENTRY (20, 14h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-030 |DUMP TABLE ENTRY (30, 1Eh)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-031 |DUMP TABLE (31, 1Fh)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-047 |SET OUTPUT PULSE (47, 2Fh)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-048 |SET OUTPUT (48, 30h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-049 |SET OUTPUT INIT (49, 31h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-057 |DUMP OUTPUT PULSE (57, 39h)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-058 |DUMP OUTPUT (58, 3Ah)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-059 |DUMP OUTPUT INIT (59, 3Bh)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-125 |I2C PORT (125, 7Dh)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-126 |I2C WRITE (126, 7Eh)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-124 |I2C WRITE SINGLE (124, 7Ch)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-127 |I2C READ (127, 7Fh)]] |
| − | *[[Firmware- | + | *[[Firmware-751 Command-122 |I2C READ SINGLE (122, 7Ah)]] |
Latest revision as of 03:12, 11 January 2018
General
This section describes the messages and commands for resetting the USB-microDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting MIDI out operation, setting running status and obtaining COM port status. These commands have the same effect both in stand-alone and host mode.
Standalone Mode
This section describes the programming protocol commands sent to the USB-microDig specifically for stand-alone mode.
Dual Mode
This section describes the programming protocol commands sent to the USB-microDig to configure sensor inputs and actuator outputs that can be used in both host mode and stand-alone mode.
