Difference between revisions of "Firmware-641 Commands"
| Line 1: | Line 1: | ||
| − | Since many firmware 6.41 commands are the same as used in firmware 8. | + | Since many firmware 6.41 commands are the same as used in firmware 8.11, reference is made to firmware 8.11 information where applicable. |
==General== | ==General== | ||
| Line 5: | Line 5: | ||
This section describes the messages and commands for resetting the Wi-microDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting MIDI out operation, setting running status and obtaining the Bluetooth port status. These commands have the same effect both in stand-alone and host mode. | This section describes the messages and commands for resetting the Wi-microDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting MIDI out operation, setting running status and obtaining the Bluetooth port status. These commands have the same effect both in stand-alone and host mode. | ||
| − | *[[Firmware- | + | *[[Firmware-811 Command-034 |RESET (34, 22h)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-060 |OUTPUT INIT (60, 3Ch)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-071 |DUMP VERSION (71, 47h)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-066 |DUMP FIRMWARE VERSION (66, 42h)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-090 |SET MODE (90, 5Ah)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-091 |DUMP MODE (91, 5Bh)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-092 |SET ID (92, 5Ch)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-032 |SET SOLO (32, 20h)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-033 |DUMP SOLO (33, 21h)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-050 |SET MUTE (50, 32h)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-051 |DUMP MUTE (51, 33h)]] |
*[[Firmware-641 Command-111 |LOW POWER THRESHOLD (111, 6Fh)]] | *[[Firmware-641 Command-111 |LOW POWER THRESHOLD (111, 6Fh)]] | ||
| Line 28: | Line 28: | ||
This section describes the programming protocol commands sent to the USB-microDig specifically for stand-alone mode. | This section describes the programming protocol commands sent to the USB-microDig specifically for stand-alone mode. | ||
| − | *[[Firmware- | + | *[[Firmware-811 Command-100 |EDIT NAME (100, 64h)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-101 |DUMP NAME (101, 65h)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-105 |CLEAR CONFIG (105, 69h)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-106 |EDIT CONFIG (106, 6Ah)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-107 |DUMP CONFIG (107, 6Bh)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-108 |DUMP ALL CONFIG (108, 6Ch)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-109 |DUMP CONFIG RANGE (109, 6Dh)]] |
| Line 42: | Line 42: | ||
This section describes the programming protocol commands sent to the USB-microDig to configure sensor inputs and actuator outputs that can be used in both host mode and stand-alone mode. | This section describes the programming protocol commands sent to the USB-microDig to configure sensor inputs and actuator outputs that can be used in both host mode and stand-alone mode. | ||
| − | *[[Firmware- | + | *[[Firmware-811 Command-001 |STREAM (1, 01h)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-011 |DUMP STREAM (11, 0Bh)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-002 |RES (2, 02h)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-012 |DUMP RES (12, 0Ch)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-004 |SAMPLE (4, 04h)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-003 |INTERVAL (3, 03h)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-013 |DUMP INTERVAL (13, 0Dh)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-008 |FUNCTION (8, 08h)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-018 |DUMP FUNCTION (18, 12h)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-125 |I2C PORT (125, 7Dh)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-126 |I2C WRITE (126, 7Eh)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-124 |I2C WRITE SINGLE (124, 7Ch)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-127 |I2C READ (127, 7Fh)]] |
| − | *[[Firmware- | + | *[[Firmware-811 Command-122 |I2C READ SINGLE (122, 7Ah)]] |
Latest revision as of 03:29, 27 July 2020
Since many firmware 6.41 commands are the same as used in firmware 8.11, reference is made to firmware 8.11 information where applicable.
General
This section describes the messages and commands for resetting the Wi-microDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting MIDI out operation, setting running status and obtaining the Bluetooth port status. These commands have the same effect both in stand-alone and host mode.
Standalone Mode
This section describes the programming protocol commands sent to the USB-microDig specifically for stand-alone mode.
- CLEAR CONFIG (105, 69h)
- EDIT CONFIG (106, 6Ah)
- DUMP CONFIG (107, 6Bh)
- DUMP ALL CONFIG (108, 6Ch)
- DUMP CONFIG RANGE (109, 6Dh)
Dual Mode
This section describes the programming protocol commands sent to the USB-microDig to configure sensor inputs and actuator outputs that can be used in both host mode and stand-alone mode.
