Difference between revisions of "Firmware-780 Messages"
(Copied from Firmware-770 Messages, revision 5824) |
|||
| Line 1: | Line 1: | ||
Note that in the following listing the commands as echoed back by the USB-microDig (to allow multiple Max/MSP objects to work with a USB-microDig) are not included. | Note that in the following listing the commands as echoed back by the USB-microDig (to allow multiple Max/MSP objects to work with a USB-microDig) are not included. | ||
| − | Since most firmware 7. | + | Since most firmware 7.80 commands are the same as used in firmware 8.30, reference is made to firmware 8.30 information where applicable. |
==General== | ==General== | ||
| − | *[[Firmware- | + | *[[Firmware-830_Message-033 |SOLO (33, 21h)]] |
| − | *[[Firmware- | + | *[[Firmware-830_Message-035 |RESET ACK (35, 23h)]] |
| − | *[[Firmware- | + | *[[Firmware-830_Message-037 |STATUS (37, 25h)]] |
| − | *[[Firmware- | + | *[[Firmware-830_Message-051 |MUTE (51, 33h)]] |
| − | *[[Firmware- | + | *[[Firmware-830_Message-066 |FIRMWARE (66, 42h)]] |
| − | *[[Firmware- | + | *[[Firmware-830_Message-071 |VERSION (71, 47h)]] |
| − | *[[Firmware- | + | *[[Firmware-830_Message-091 |MODE (91, 5Bh)]] |
*[[Firmware-770_Message-096 |MIDI OUT (96, 60h)]] | *[[Firmware-770_Message-096 |MIDI OUT (96, 60h)]] | ||
*[[Firmware-770_Message-095 |MIDI CONFIG (95, 60h)]] | *[[Firmware-770_Message-095 |MIDI CONFIG (95, 60h)]] | ||
| Line 20: | Line 20: | ||
==Standalone Mode== | ==Standalone Mode== | ||
| − | *[[Firmware- | + | *[[Firmware-830_Message-101 |NAME (101, 65h)]] |
| − | *[[Firmware- | + | *[[Firmware-830_Message-107 |CONFIG (107, 6Bh)]] |
==Dual Mode== | ==Dual Mode== | ||
| − | *[[Firmware- | + | *[[Firmware-830_Message-000 |STREAM DATA (0, 00h)]] |
| − | *[[Firmware- | + | *[[Firmware-830_Message-004 |SAMPLE DATA (4, 04h)]] |
| − | *[[Firmware- | + | *[[Firmware-830_Message-010 |I2C DATA (10, 0Ah)]] |
| − | *[[Firmware- | + | *[[Firmware-830_Message-125 |I2C PORT (125, 7Dh)]] |
| − | *[[Firmware- | + | *[[Firmware-830_Message-123 |I2C NO RESPONSE (123, 7Bh)]] |
| − | *[[Firmware- | + | *[[Firmware-830_Message-126 |I2C WRITE (126, 7Eh)]] |
| − | *[[Firmware- | + | *[[Firmware-830_Message-127 |I2C READ (127, 7Fh)]] |
| − | *[[Firmware- | + | *[[Firmware-830_Message-124 |I2C WRITE SINGLE (124, 7Ch)]] |
| − | *[[Firmware- | + | *[[Firmware-830_Message-122 |I2C READ SINGLE (122, 7Ah)]] |
Revision as of 02:12, 2 May 2023
Note that in the following listing the commands as echoed back by the USB-microDig (to allow multiple Max/MSP objects to work with a USB-microDig) are not included.
Since most firmware 7.80 commands are the same as used in firmware 8.30, reference is made to firmware 8.30 information where applicable.
General
- SOLO (33, 21h)
- RESET ACK (35, 23h)
- STATUS (37, 25h)
- MUTE (51, 33h)
- FIRMWARE (66, 42h)
- VERSION (71, 47h)
- MODE (91, 5Bh)
- MIDI OUT (96, 60h)
- MIDI CONFIG (95, 60h)
- LOW POWER AND COM (111, 6Fh)
Standalone Mode
