Difference between revisions of "Firmware-633 Commands"
| (10 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | Since many firmware 6. | + | Since many firmware 6.33 commands are the same as used in firmware 7.3/7.33, reference is made to firmware 7.3/7.33 information where applicable. |
==General== | ==General== | ||
| Line 8: | Line 8: | ||
*[[Firmware-73 Command-060 |OUTPUT INIT (60, 3Ch)]] | *[[Firmware-73 Command-060 |OUTPUT INIT (60, 3Ch)]] | ||
| − | *[[Firmware- | + | *[[Firmware-733 Command-071 |DUMP VERSION (71, 47h)]] |
| + | *[[Firmware-733 Command-066 |DUMP FIRMWARE VERSION (66, 42h)]] | ||
*[[Firmware-73 Command-090 |SET MODE (90, 5Ah)]] | *[[Firmware-73 Command-090 |SET MODE (90, 5Ah)]] | ||
| Line 30: | Line 31: | ||
This section describes the programming protocol commands sent to the USB-microDig specifically for stand-alone mode. | This section describes the programming protocol commands sent to the USB-microDig specifically for stand-alone mode. | ||
| − | *[[Firmware- | + | *[[Firmware-633 Command-100 |EDIT NAME (100, 64h)]] |
| − | *[[Firmware- | + | *[[Firmware-633 Command-101 |DUMP NAME (101, 65h)]] |
| − | |||
| − | |||
| − | |||
| − | |||
| + | *[[Firmware-633 Command-105 |CLEAR CONFIG (105, 69h)]] | ||
| + | *[[Firmware-633 Command-106 |EDIT CONFIG (106, 6Ah)]] | ||
| + | *[[Firmware-633 Command-107 |DUMP CONFIG (107, 6Bh)]] | ||
==Dual Mode== | ==Dual Mode== | ||
| Line 54: | Line 54: | ||
*[[Firmware-73 Command-018 |DUMP FUNCTION (18, 12h)]] | *[[Firmware-73 Command-018 |DUMP FUNCTION (18, 12h)]] | ||
| − | *[[Firmware- | + | *[[Firmware-633 Command-048 |SET OUTPUT (48, 30h)]] |
| − | + | *[[Firmware-633 Command-049 |SET OUTPUT INIT (49, 31h)]] | |
| − | *[[Firmware- | + | *[[Firmware-633 Command-058 |DUMP OUTPUT (58, 3Ah)]] |
| − | *[[Firmware- | + | *[[Firmware-633 Command-059 |DUMP OUTPUT INIT (59, 3Bh)]] |
| − | |||
| − | *[[Firmware- | ||
*[[Firmware-73 Command-125 |I2C PORT (125, 7Dh)]] | *[[Firmware-73 Command-125 |I2C PORT (125, 7Dh)]] | ||
Latest revision as of 20:38, 4 December 2018
Since many firmware 6.33 commands are the same as used in firmware 7.3/7.33, reference is made to firmware 7.3/7.33 information where applicable.
General
This section describes the messages and commands for resetting the Wi-microDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting MIDI out operation, setting running status and obtaining the Bluetooth port status. These commands have the same effect both in stand-alone and host mode.
Standalone Mode
This section describes the programming protocol commands sent to the USB-microDig specifically for stand-alone mode.
Dual Mode
This section describes the programming protocol commands sent to the USB-microDig to configure sensor inputs and actuator outputs that can be used in both host mode and stand-alone mode.
