Difference between revisions of "Firmware-641 Messages"
| (3 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
Note that in the following listing the commands as echoed back by the Wi-microDig (to allow multiple Max/MSP objects to work with a Wi-microDig) are not included. | Note that in the following listing the commands as echoed back by the Wi-microDig (to allow multiple Max/MSP objects to work with a Wi-microDig) are not included. | ||
| − | Since many firmware 6.41 messages are the same as used in firmware 8. | + | Since many firmware 6.41 messages are the same as used in firmware 8.11, reference is made to firmware 8.11 information where applicable. |
==General== | ==General== | ||
| − | *[[Firmware- | + | *[[Firmware-811_Message-033 |SOLO (33, 21h)]] |
| − | *[[Firmware- | + | *[[Firmware-811_Message-035 |RESET ACK (35, 23h)]] |
| − | *[[Firmware- | + | *[[Firmware-811_Message-037 |STATUS (37, 25h)]] |
| − | *[[Firmware- | + | *[[Firmware-811_Message-071 |VERSION (71, 47h)]] |
| − | *[[Firmware- | + | *[[Firmware-811_Message-066 |FIRMWARE VERSION (66, 42h)]] |
| − | *[[Firmware- | + | *[[Firmware-811_Message-091 |MODE (91, 5Bh)]] |
*[[Firmware-641_Message-111 |LOW POWER LEVEL (111, 6Fh)]] | *[[Firmware-641_Message-111 |LOW POWER LEVEL (111, 6Fh)]] | ||
*[[Firmware-640_Message-114 |BATTERY VOLTAGE LEVEL (114, 6Fh)]] | *[[Firmware-640_Message-114 |BATTERY VOLTAGE LEVEL (114, 6Fh)]] | ||
| Line 18: | Line 18: | ||
==Standalone Mode== | ==Standalone Mode== | ||
| − | *[[Firmware- | + | *[[Firmware-811_Message-101 |NAME (101, 65h)]] |
| − | *[[Firmware- | + | *[[Firmware-811_Message-107 |CONFIG (107, 6Bh)]] |
==Dual Mode== | ==Dual Mode== | ||
| − | *[[Firmware- | + | *[[Firmware-811_Message-000 |STREAM DATA (0, 00h)]] |
| − | *[[Firmware- | + | *[[Firmware-811_Message-004 |SAMPLE DATA (4, 04h)]] |
| − | *[[Firmware- | + | *[[Firmware-811_Message-010 |I2C DATA (10, 0Ah)]] |
| − | *[[Firmware- | + | *[[Firmware-811_Message-125 |I2C PORT (125, 7Dh)]] |
| − | *[[Firmware- | + | *[[Firmware-811_Message-123 |I2C NO RESPONSE (123, 7Bh)]] |
| − | *[[Firmware- | + | *[[Firmware-811_Message-126 |I2C WRITE (126, 7Eh)]] |
| − | *[[Firmware- | + | *[[Firmware-811_Message-127 |I2C READ (127, 7Fh)]] |
Latest revision as of 03:34, 27 July 2020
Note that in the following listing the commands as echoed back by the Wi-microDig (to allow multiple Max/MSP objects to work with a Wi-microDig) are not included.
Since many firmware 6.41 messages are the same as used in firmware 8.11, reference is made to firmware 8.11 information where applicable.
General
- SOLO (33, 21h)
- RESET ACK (35, 23h)
- STATUS (37, 25h)
- VERSION (71, 47h)
- FIRMWARE VERSION (66, 42h)
- MODE (91, 5Bh)
- LOW POWER LEVEL (111, 6Fh)
- BATTERY VOLTAGE LEVEL (114, 6Fh)
Standalone Mode
