Difference between revisions of "Firmware-72 Messages"
(Created page with "==General== RESET ACK (35, 23h) STATUS (37, 25h) VERSION (71, 47h) Firmware-72_Messag...") |
(→Dual Mode) |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| + | Note that in the following listing the commands as echoed back by the USB-microDig (to allow multiple Max/MSP objects to work with a USB-microDig) are not included. | ||
| + | |||
| + | |||
==General== | ==General== | ||
| − | [[Firmware-72_Message-035 |RESET ACK (35, 23h)]] | + | *[[Firmware-72_Message-035 |RESET ACK (35, 23h)]] |
| − | [[Firmware-72_Message-037 |STATUS (37, 25h)]] | + | *[[Firmware-72_Message-037 |STATUS (37, 25h)]] |
| − | [[Firmware-72_Message-071 |VERSION (71, 47h)]] | + | *[[Firmware-72_Message-071 |VERSION (71, 47h)]] |
| − | [[Firmware-72_Message-091 |MODE (91, 5Bh)]] | + | *[[Firmware-72_Message-091 |MODE (91, 5Bh)]] |
| − | [[Firmware-72_Message-096 |MIDI OUT (96, 60h)]] | + | *[[Firmware-72_Message-096 |MIDI OUT (96, 60h)]] |
| − | [[Firmware-72_Message-095 |RUNNING (95, 60h)]] | + | *[[Firmware-72_Message-095 |RUNNING STATUS (95, 60h)]] |
| − | [[Firmware-72_Message-111 |COM (111, 6Fh)]] | + | *[[Firmware-72_Message-111 |COM (111, 6Fh)]] |
==Standalone Mode== | ==Standalone Mode== | ||
| − | [[Firmware-72_Message-101 |NAME (101, 65h)]] | + | *[[Firmware-72_Message-101 |NAME (101, 65h)]] |
| − | [[Firmware-72_Message-106 |CONFIG (106, 6Ah)]] | + | *[[Firmware-72_Message-106 |CONFIG (106, 6Ah)]] |
==Dual Mode== | ==Dual Mode== | ||
| − | [[Firmware-72_Message-000 |STREAM DATA (0, 00h)]] | + | *[[Firmware-72_Message-000 |STREAM DATA (0, 00h)]] |
| − | [[Firmware-72_Message-004 |SAMPLE DATA (4, 04h)]] | + | *[[Firmware-72_Message-004 |SAMPLE DATA (4, 04h)]] |
| − | [[Firmware-72_Message-010 |I2C DATA (10, | + | *[[Firmware-72_Message-010 |I2C DATA (10, 0Ah)]] |
| − | [[Firmware-72_Message-125 |I2C PORT (125, 7Dh)]] | + | *[[Firmware-72_Message-125 |I2C PORT (125, 7Dh)]] |
| − | [[Firmware-72_Message-123 |I2C NO RESPONSE (123, 7Bh)]] | + | *[[Firmware-72_Message-123 |I2C NO RESPONSE (123, 7Bh)]] |
| − | [[Firmware-72_Message-126 |I2C WRITE (126, 7Eh)]] | + | *[[Firmware-72_Message-126 |I2C WRITE (126, 7Eh)]] |
| − | [[Firmware-72_Message-127 |I2C READ (127, 7Fh)]] | + | *[[Firmware-72_Message-127 |I2C READ (127, 7Fh)]] |
Latest revision as of 17:07, 19 June 2017
Note that in the following listing the commands as echoed back by the USB-microDig (to allow multiple Max/MSP objects to work with a USB-microDig) are not included.
General
- RESET ACK (35, 23h)
- STATUS (37, 25h)
- VERSION (71, 47h)
- MODE (91, 5Bh)
- MIDI OUT (96, 60h)
- RUNNING STATUS (95, 60h)
- COM (111, 6Fh)
Standalone Mode
