Difference between revisions of "Firmware-73 Commands"
(Created page with " ==General== This section describes the messages and commands for resetting the USB-microDig, obtaining version information, setting the mode of operation (stand-alone or hos...") |
|||
| Line 4: | Line 4: | ||
This section describes the messages and commands for resetting the USB-microDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting MIDI out operation, setting running status and obtaining COM port status. These commands have the same effect both in stand-alone and host mode. | This section describes the messages and commands for resetting the USB-microDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting MIDI out operation, setting running status and obtaining COM port status. These commands have the same effect both in stand-alone and host mode. | ||
| − | *[[Firmware- | + | *[[Firmware-73 Command-034 |RESET (34, 22h)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-060 |OUTPUT INIT (60, 3Ch)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-071 |DUMP VERSION (71, 47h)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-090 |SET MODE (90, 5Ah)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-091 |DUMP MODE (91, 5Bh)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-092 |SET ID (92, 5Ch)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-032 |MUTE (32, 20h)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-050 |SET MUTE (50, 32h)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-093 |MIDI OUT (93, 5Dh)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-096 |DUMP MIDI OUT (96, 60h)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-094 |MIDI RUNNING STATUS (94, 5Eh)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-095 |DUMP RUNNING STATUS (95, 5Fh)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-111 |DUMP COM (111, 6Fh)]] |
| Line 30: | Line 30: | ||
This section describes the programming protocol commands sent to the USB-microDig specifically for stand-alone mode. | This section describes the programming protocol commands sent to the USB-microDig specifically for stand-alone mode. | ||
| − | *[[Firmware- | + | *[[Firmware-73 Command-100 |EDIT NAME (100, 64h)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-101 |DUMP NAME (101, 65h)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-105 |CLEAR CONFIG (105, 69h)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-106 |EDIT CONFIG (106, 6Ah)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-107 |DUMP CONFIG (107, 6Bh)]] |
| Line 42: | Line 42: | ||
This section describes the programming protocol commands sent to the USB-microDig to configure sensor inputs and actuator outputs that can be used in both host mode and stand-alone mode. | This section describes the programming protocol commands sent to the USB-microDig to configure sensor inputs and actuator outputs that can be used in both host mode and stand-alone mode. | ||
| − | *[[Firmware- | + | *[[Firmware-73 Command-001 |STREAM (1, 01h)]] |
| − | *[[Firmware- | + | *[[Firmware-73 Command-002 |RES (2, 02h)]] |
*[[Firmware-73 Command-004 |SAMPLE (4, 04h)]] | *[[Firmware-73 Command-004 |SAMPLE (4, 04h)]] | ||
Revision as of 00:15, 12 November 2016
General
This section describes the messages and commands for resetting the USB-microDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting MIDI out operation, setting running status and obtaining COM port status. These commands have the same effect both in stand-alone and host mode.
Standalone Mode
This section describes the programming protocol commands sent to the USB-microDig specifically for stand-alone mode.
Dual Mode
This section describes the programming protocol commands sent to the USB-microDig to configure sensor inputs and actuator outputs that can be used in both host mode and stand-alone mode.
