Difference between revisions of "Firmware-820 Commands"
(→General) |
|||
| Line 5: | Line 5: | ||
This section describes the messages and commands for resetting the WiDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting BLE-MIDI out operation and setting running status and obtaining MIDI status. These commands have the same effect both in stand-alone and host mode. | This section describes the messages and commands for resetting the WiDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting BLE-MIDI out operation and setting running status and obtaining MIDI status. These commands have the same effect both in stand-alone and host mode. | ||
| − | *[[Firmware- | + | *[[Firmware-820 Command-034 |RESET (34, 22h)]] |
| − | *[[Firmware- | + | *[[Firmware-820 Command-060 |OUTPUT INIT (60, 3Ch)]] |
| − | *[[Firmware- | + | *[[Firmware-820 Command-066 |DUMP FIRMWARE VERSION (66, 42h)]] |
| − | *[[Firmware- | + | *[[Firmware-820 Command-071 |DUMP VERSION (71, 47h)]] |
| − | *[[Firmware- | + | *[[Firmware-820 Command-090 |SET MODE (90, 5Ah)]] |
| − | *[[Firmware- | + | *[[Firmware-820 Command-091 |DUMP MODE (91, 5Bh)]] |
| − | *[[Firmware- | + | *[[Firmware-820 Command-092 |SET ID (92, 5Ch)]] |
| − | *[[Firmware- | + | *[[Firmware-820 Command-032 |SET SOLO (32, 20h)]] |
| − | *[[Firmware- | + | *[[Firmware-820 Command-033 |DUMP SOLO (33, 21h)]] |
| − | *[[Firmware- | + | *[[Firmware-820 Command-050 |SET MUTE (50, 32h)]] |
| − | *[[Firmware- | + | *[[Firmware-820 Command-051 |DUMP MUTE (51, 33h)]] |
| − | *[[Firmware- | + | *[[Firmware-820 Command-093 |BLE-MIDI (93, 5Dh)]] |
| − | *[[Firmware- | + | *[[Firmware-820 Command-096 |DUMP BLE-MIDI (96, 60h)]] |
| − | *[[Firmware- | + | *[[Firmware-820 Command-094 |MIDI CONFIG (94, 5Eh)]] |
| − | *[[Firmware- | + | *[[Firmware-820 Command-095 |DUMP MIDI CONFIG (95, 5Fh)]] |
*[[Firmware-812 Command-111 |LOW POWER (111, 6Fh)]] | *[[Firmware-812 Command-111 |LOW POWER (111, 6Fh)]] | ||
| − | |||
==Standalone Mode== | ==Standalone Mode== | ||
Revision as of 23:37, 6 March 2022
Since many firmware 8.20 commands are the same as used in firmware 8.11 and 8.12, reference is made to firmware 8.11 or 8.12 information where applicable.
General
This section describes the messages and commands for resetting the WiDig, obtaining version information, setting the mode of operation (stand-alone or host mode), setting the device ID, setting BLE-MIDI out operation and setting running status and obtaining MIDI status. These commands have the same effect both in stand-alone and host mode.
Standalone Mode
This section describes the programming protocol commands sent to the WiDig specifically for stand-alone mode.
- CLEAR CONFIG (105, 69h)
- EDIT CONFIG (106, 6Ah)
- DUMP CONFIG (107, 6Bh)
- DUMP ALL CONFIG (108, 6Ch)
- DUMP CONFIG RANGE (109, 6Dh)
Dual Mode
This section describes the programming protocol commands sent to the WiDig to configure sensor inputs and actuator outputs that can be used in both host mode and stand-alone mode.
